How to Keep Dog From Jumping Baby Gate

Dog Gate Use Ofttimes Asked Questions

Why should I cull Retract-A-Gate?

Once the Mounting Brackets are installed, snap the retractable safety gate into the brackets. The dog gate is interchangeable, and so it can be attached to either side of the installation expanse as desired. The safety gate operates past pulling the handle out from the reel of the gate and hooking it in place to the mounting brackets installed at the opposite side of the installation. Once the gate is hooked into the brackets, push and plow the locking mechanism to lock the gate in identify. You are at present able to keep your dogs contained!

Our retractable domestic dog gates are secured by a canis familiaris-proof push button and turn locking machinery. Because of this, the retractable gate can be locked at any width up to the maximum width of the gate. Locking the retractable safety gate prevents information technology from being pushed out or pulled down. When you want to pass through the safety gate, simply push and plough the safety locking mechanism to unlock it, unhook the handle side from the brackets, and then guide the handle back into the reel side of the domestic dog gate.

Retract-A-Gate retracts utilizing an internal spring which automatically rewinds the mesh so no manual winding is required. The mesh can only be rewound when the lock has been turned to the open position; and the retraction is repose, smooth, and steady. The mesh and handle are neatly contained in the reel when fully retracted. Retract-A-Gate is the Only retractable safety gate which retracts easily, quietly, and automatically. Because the performance of the domestic dog gate is simple, information technology can exist washed with ane hand, and just takes a few seconds to do. Our retractable safety gates were engineered and designed with both safety AND convenience in listen and we are confident that you volition be satisfied.

Please refer to our Install and Specs page for employ and installation instructions and visit our Dog Gate Videos and Reviews folio to see Retract-A-Gate in action and hear straight from our customers how much they dear their Retract-A-Gate.

Retract-A-Gate was designed from the ground upward to offer our customers the best functioning and quality gate on the market. Nosotros have extensively tested the other retractable gates for dogs and have institute that the main divergence between the Retract-A-Gate and the other gates on the market is simply quality. Retract-A-Gate is priced very competitively when yous consider the overall quality and value. No other safety gate is as piece of cake to utilise while keeping your little ones safer. Many of our competitors have complicated parts that are difficult to apply. Oftentimes times their gates will not stand up to extended utilise, or they even break easily. You become what you pay for and when it comes to safety, durability, and ease of use, look no farther than Retract-A-Gate! Here is a quick list of why Retract-A-Gate is the all-time selection:

• Other canis familiaris gates make a loud ratcheting sound when information technology is retracted; Retract-A-Gate is placidity.
• Retract-A-Gate automatically rewinds when retracted. Some of our competitors require manual rewinding of the mesh.
• Most other retractable gates cannot be easily operated with one hand. Retract-A-Gate truly has unproblematic, i-hand utilize.

Watch our dog gate videos here!

• Other retractable gates for dogs use complex parts to install them; Retract-A-Gate mounting hardware is simple and piece of cake to install.
• While retracting some of our competitor's gates, pausing while opening or closing causes them to jam. Retract-A-Gate was engineered to avoid this cumbersome method of use and operates smoothly.
• Retract-A-Gate is made in the U.Due south.A. while well-nigh other gates are made cheaply overseas.
• The mounting hardware for other gates is obvious and stands out; Retract-A-Gate mounting brackets alloy in to their surround, are clear in color, and extremely durable.
• Retract-A-Gate may be used indoors and outdoors for virtually whatever installation imaginable.
• The widest our competitors' retractable gates can encompass is 55 inches. The Retract-A-Gate extra wide retractable gate can encompass openings upwardly to 72 inches.
• Retract-A-Gates can exist connected together to encompass wider distances than 72 inches if used for non-critical applications (not for use at the top of stairs). No other retractable gate can do this.
• The mounting brackets for the Retract-A-Gate are universal which means that the doggy gate tin can be quickly relocated to another area.
• Retract-A-Gate is 34 inches tall which is one of the tallest pet gates available.
• The tough mesh material allows the gate to exist used for more than your dog. Retract-A-Gate was engineered for utilize with both children AND pets.
• Many gates are non easy to utilize or are not prophylactic. Retract-A-Gate is truly the highest quality, elementary to utilize, retractable safety gate available.

Do I demand anything earlier ordering or installing Retract-A-Gate?

When installing the Retract-A-Gate, there are a few measurements of your installation that you volition demand to know before you order.

The first measurement you volition need to know is the width of the opening you lot want to install the gate. We offer two Retract-A-Gate models that are 52 and 72 inches broad. These widths are the total altitude (gate and brackets) that the dog gate can cover if the gate is installed within an opening. The mounting brackets are about 2.five inches wide so if you don't have the 2.5 inches of surface expanse necessary to mount your retractable gate, the brackets can also mountain around the corner of the doorway, either on the door molding or on the wall. If you install the gate on the outside of an opening however, the mounting brackets will not contribute to the maximum width of the gate.

The next measurement you will demand for installation is the position of the brackets. The wall brackets must be mounted about 3 and 30.5 inches off the floor and require about ii.5 inches of flat surface to attach to. The positioning of the brackets can be adjusted about an inch up and down if necessary.

Some other measurements that are dainty to know are the top of the mesh, the height of the lock, and the size of the gate when retracted. The height of the scratch resistant mesh is 34 inches and the total meridian to the pinnacle of the lock is less than 38 inches. When completely retracted, Retract-A-Gate is less than 4 inches in diameter. When the retractable dog gate is mounted within a doorway, most doors will nevertheless be able to shut with the mounting hardware and dog gate in identify.

The concluding measurement you volition need is if there are baseboards where you will exist installing your Retract-A-Gate. You lot must measure out the height and thickness of your baseboard to determine if the lesser bracket needs to be installed to the baseboard. If this is the case, or if the baseboard is thicker than 0.25 inches, you will need a Wall Spacer Set. For more data on wall spacers, become to the Wall Spacer department on our Online Store page where all the information most whether you will demand a spacer ready or not is located.

For a normal doorway, hallway, or walk-style installation with the subclass screws attached into a solid wall or molding that is affluent to the floor with no obstructions (no stairs or baseboard interference), no other accessories should exist needed and the installation parts that come with each gate should be sufficient. For other installations where baseboards are present or for other more complicated installations on stairs, for example, nosotros accept several accessories available to make those installations piece of cake. More information about each of our accessories and whether yous need them can be found on our Online Shop page.

What practise I demand to exercise to install Retract-A-Gate?

Yes! Retract-A-Gate is certified and extensively tested for use at the top and bottom of the stairs and because of the safety gate's engineering and blueprint; it can withstand a push out force of upward to 200 pounds. With many staircases, often-times you will need to install to a banister post one of 2 ways. The beginning is to attach the wall brackets directly onto your baluster or newel post (stair mail service). In club to install this fashion, your banister post needs to have a 3-inch-broad flat surface at nigh 3-4 and 30.5 inches from the flooring for the mounting brackets to exist screwed into. The 2nd way is needed if your banister postal service is circular in shape or is less than three inches wide where the brackets demand to adhere, then you tin can use the Stair Banister Adapter Kit found on our Online Store. The brackets that come with each domestic dog gate spiral into the adapter, then that associates straps to your stair post using the straps provided with the kit. The Banister Adapter can adjust banister posts or spindles that are upwards to 7 inches by vii inches in size. If attaching to smaller spindles, our Banister Adapters are designed with a groove in the dorsum of the adapter that is able to fit effectually spindles or atomic number 26 posts about 1 inch or less.

When installing at the top of stairs we recommend you mount the retractable safety gate a minimum of half-dozen inches back from the border of the acme pace. Because the mesh of the gate is fabricated of a flexible cloth, if installed at the border of the top pace, the mesh can be pushed out a few inches which will create a gap at the bottom of the gate. If this is a trouble for you, the Retract-A-Gate tin can be installed diagonally away from the top step, which can assistance reach the half dozen-inch requirement. See FAQ #half-dozen for more information. If fishing the retractable canis familiaris gate also is not an option, you may be able to block off near-by passage means that would restrict admission to the stairs.

When installing at the bottom of stairs, we recommend mounting the Retract-A-Gate on the floor in front of the steps to keep it at the lowest level. This helps to minimize the gamble of falls from a higher spot. Some layouts may not be conducive to permit for an easy installation at the lowest level, however, due to curved steps or recessed walls. For those configurations, installing upward a step can be done if sure safe considerations are taken. If you have a stairs configuration like this, contact usa if you need help determining the all-time way to install Retract-A-Gate on a step.

If you are going to attach both sides of your dog gate to stair posts or spindles, you lot will need two Banister Adapter Kits (i adapter for each post). Nosotros offer 36 inch tall and 48 inch tall adapters. The 36-inch adapter will work for virtually installations, but we offer the 48-inch adapter if you are installing to a taller post(s). Some posts are rounded in unlike areas or are narrow in the middle. The adapter will span over narrow or rounded areas to provide a surface to install the brackets to. If the distance from the floor to the area of the mail that the adapter must reach is greater than 36 inches, you will need the 48-inch adapter. If the adapter is too tall for your needs, it can be cutting shorter (using a saw) to avoid standing taller than your stair mail. If you cut your adapter, exercise not cut it shorter than 32 inches. More detailed information and total installation instructions can be institute on our Install & Specs Page.

Yep! The Mounting Brackets that the gate hooks into allows the dog gate to pivot at any angle up to 180 degrees which will open upwards numerous mounting options. Well-nigh other retractable domestic dog gates on the market do not accept this power. If installing at the peak of stairs, the Retract-A-Gate can be angled away from the stairs to increase the gap betwixt the gate and the top footstep in gild to accomplish the required 6 inch gap between the gate and the top pace. If installing the gate for dogs at an angle, be certain to install the brackets then the opening of the brackets are facing away from the gate.

The Retract-A-Gate is versatile and therefore tin be mounted near anywhere to virtually any surface. Other than installing to drywall, some other mutual installation surfaces are listed below forth with what y'all need to consider for that surface.

Bookcase or cabinet: We recommend installing to a bookcase or a chiffonier only if the bookcase or chiffonier is stable (wall-mounted). The screws that come with the gate are 2 inches long so you may need to put a capitalist board on the inside wall of the bookcase (or cabinet) if the wall is sparse. If the cabinet walls are thin, the backer board will allow the screws to seize with teeth into more wood, will assistance strengthen the wall, and volition minimize screws poking through the wall of the cabinet or bookcase. If installing to a cabinet with a counter top overhang, the wall spacers or blocks of forest tin be used under both the peak and bottom brackets to push the brackets out from under the overhang and allow the safety gate to be attached.

Brick, stone, physical, or mortar: The hardware that comes with the gate can only be used for wooden surfaces. If installing to brick, stone, concrete, or mortar, you will need appropriate masonry anchors which you can buy at any hardware store. Just accept our screws to your hardware shop and take them size an appropriate masonry ballast for you. If you lot need to use different length screws than the ones provided, you will need a #6 flathead screw to fit the included finishing washers. When installing to stone or rough textured surfaces which do not provide apartment surfaces for the brackets, another option for installation would exist to spike a lath to the surface using similar anchors and then attach the brackets to the lath using the wood screws that come with the gate.

Fiberglass: The mounting screws volition not hold in fiberglass lonely. We always recommend mounting the brackets to the back up/stud behind the fiberglass if possible; otherwise you need to utilize appropriate anchors or a backer board that will work with your fiberglass.

Vinyl siding on a house: Yous cannot attach the brackets to vinyl siding alone, however, if in that location is solid wood sheeting/boards underneath the siding (this is usually the case) then yous will be able to install the brackets there.

Of form! Our dog gate has been extensively tested in outdoor uses with flawless results. Our facility is in Dubuque, IA and we take besides tested the retractable safe gate exterior during a full Iowa winter, again, with flawless results. When installed outdoors, we do recommend you bring the Retract-A-Gate inside during freezing temperatures to help go on the mechanisms from beingness affected with snow or ice build-upward.

We practice have a disclaimer for outdoor use. Anything, including a Retract-A-Gate, which is left outside will have a shorter lifespan when compared to only indoor use. Retract-A-Gate has been designed to be UV resistant, however something to be aware of is that some fading or degradation due to extended sun exposure is possible, but overall, those furnishings should be minimal.

If you lot are installing to Trex or composite decking, the composite posts volition normally have a 4×4 treated or cedar mail inside them. If this is the case, we recommend pre-drilling the screw holes and using #vi flat head stainless steel screws the same size every bit the ones we provide. Stainless steel will hold upwards the best when used with treated wood which is ordinarily used for outdoor decks, patios and other structures. You can as well attach the wall brackets to your business firm siding if at that place is solid wood underneath.

Currently, we are unable to make a custom size gate. With that said, at that place are a few different options yous tin choose from to encompass an opening wider than 72 inches:

Option ane: Your best bet would be to connect multiple Retract-A-Gates together using our Gate Connecter Straps. How this works is the safety gates are daisy chained together by connecting the handle rod of the 1st gate to the reel-side tie rod of the 2nd gate (and so on) as shown in the photos below. This daisy concatenation procedure can exist repeated with all the gates you would need to make upward the distance required. When using this option, the gates can still be retracted and locked using i hand. Just exist sure to recall that you must lock all the connected gates so that none of the gates continue to retract out when the barrier is pushed on by a dog.

This solution is merely for special situations such as non-critical applications or where merely a visual bulwark is needed. Hooking multiple gates together is not a certified use with children; information technology is just a special option if you are using the gates for a non-critical application similar separating two rooms and need to span an extra-long altitude. The Gate Connector Straps can be found on our Online Store.

Pick two: Another way to cover a wider opening would be to install 1 gate on the left side of the opening and another gate on the right side of the opening and connect the ii gates in the middle using the S-Hook Set. This choice can only encompass distances up to 144 inches when using ii 72-inch broad Retract-A-Gates. To connect the ii gates together, an Due south-Claw would latch the two handle rods in the elevation and the bottom cutouts (where the brackets commonly hook) as shown in the photos beneath. When using this option, you would need two easily to operate the gates and the process of retracting the gates in and out will exist slower, but still very effective to encompass a wider infinite.

This solution is as well for special situations such as low traffic areas, non-critical applications, or where only a visual bulwark is needed. Using S-Hooks to connect ii gates together is not a certified apply for children; it is just a special option for not-critical applications like separating two rooms. If you decide to use this choice, the Southward-Hooks Set is bachelor for purchase on the Online Store page.

Selection 3: A 3rd option would exist to install a partition mail in the middle of your opening that the gates could exist installed against. This would and then allow y'all to cover the opening by extending in either direction from the post.

Is the Retract-A-Gate going to work?

Retract-A-Gate has been successfully used with just about every breed of dog. With that said, some breeds of dogs like to couch and dig. For these dogs, a metal canis familiaris gate may exist your best option. Fifty-fifty when installed properly, there volition be some amount of "requite" to the mesh textile due to the fact that information technology needs to be flexible in order to retract. If the canis familiaris gate is installed incorrectly there may be too much flexibility in the mesh. Past following these guidelines, you tin can minimize most bug that could arise when using your retractable gate for dogs:

• E'er ensure the gate is locked! The retractable safety gate tin exist locked by pushing and turning the locking mechanism which will prevent the gate from retracting further. Locking the gate will besides keep the mesh taut and assistance prevent your pet from pushing the mesh out and slipping underneath.
• Be sure the base of operations of the safe gate used for dogs is resting on the floor and is not mounted upwards off the floor at all. When resting on the floor, there should exist no more than than nearly 1/4″ gap between the bottom of the mesh and the floor.
• When installing at the summit of the stairs, make sure the mesh is at least 6 inches back from the border of the step. If the gate is installed correct next to the edge of the step, the mesh could be pushed out by the edge which would create a gap that a minor pet could squeeze through.
• Both the elevation and the bottom of the prophylactic gate mesh should have no slack. If in that location is slack in the bottom of the mesh, information technology probably means the bottom brackets are likewise close to each other compared to the spacing between the 2 upper brackets. To fix this issue, create equal spacing between the 2 upper brackets and the two lower brackets. To help y'all practice this you could make your own spacer from a cake of wood or shim, or we offer Wall Spacer Sets on our Store page.
• You tin besides tighten the gate by calculation additional tension before locking the mesh in place. To do this, turn the gyre of textile (i/8 of a turn clockwise) to tighten the mesh by manus and and so, while keeping the tension, lock the gate.

Retract-A-Gate is one of the tallest available with a mesh height of 34 inches. When the gate is locked, the mesh is held in place and will not retract out any farther making it hard to push downwards. The mesh of the domestic dog gate is thinly spaced which makes the gate hard for dogs to climb over. Most dogs are unable to jump over the gate unless specifically trained or encouraged to practice so. If your dog jumps over the gate, nosotros do have an accessory Clip Prepare that tin exist found on the Online Store that allows you to install one gate over some other gate. Otherwise, you lot will need to find a taller dog gate or use a training aid to discourage your dog from trying to jump over.

What is the durability and lifespan of the gate?

The mesh of the dog gate is made from a tough, not-toxic, reinforced polymer blended. None of the gate components contain Lead, Phthalate, Latex or BPA chemicals and is formaldehyde gratuitous. The safety gate is likewise UV and Mildew resistant. Nosotros have eliminated these chemicals in all our products to avoid putting those types of chemicals around your dogs. You can see through the mesh, yet the mesh is very durable and in other applications the mesh is used as truck tarps to hold down cargo.

If you would similar a sample of the mesh, email us at info@SmartRetract.com and we will be happy to send you lot a material sample of the Café, White and Black Retract-A-Gate mesh. Merely include your proper noun and mailing address and then we can send y'all the samples.

The canis familiaris gate can be cleaned with mild soap and water. If you are dealing with stubborn stains that will not come up out with soap, you can use rubbing booze without damaging or degrading the integrity of the safety gate.

Discounts?

Nosotros've taken careful efforts to price our gates, barriers, and accessory items fairly, and because of that Retract-A-Gate offers the most value of whatever dog gate available – this is our pledge to you! We don't churn promotions or discounts on overpriced items or do other marketing tricks that cease up doing little more filling up your inbox. Our focus is on bringing yous the best retractable dog gate and the best support and service at a off-white price – making Retract-A-Gate the best value of whatever gate in its grade! On the occasions when we do have public specials or promotional drawings, we will announce those on our Online Shop in Footstep 1 of the Check Out section. If we accept a general discount or promotion to offering you, that's where it volition exist.

What is the Bow Wow Barrier and how would information technology piece of work for my dog?

Bow Wow Barrier is almost oft used on an exterior door to stop your canis familiaris or pet from getting out of your house, or if you lot prefer, from getting into your habitation, when yous open the door to exit or to greet someone. To ready the Bow Wow Barrier, starting time attach two brackets to the molding, wall, or door frame, and then attach two brackets to your door. After the brackets are installed, connect the barrier reel to the wall side and then hook the handle side into the mounting brackets attached to the door. The barrier mesh volition pull out when the door is opened or retract automatically into the Bow Wow Barrier reel when the door closes. If you need to step through the door, but unhook the handle from the brackets on the door, walk through, then just let the mesh retract into the reel. Y'all can also reattach the handle to the door to go along the bulwark in identify, and the door blocked, for the adjacent fourth dimension it opens. The Bow Wow Bulwark is very fast and like shooting fish in a barrel to use and does a great chore of keeping your dogs or pets from running out the door when y'all open it.

Here are some of the similarities and differences between the two, to assistance you make up one's mind which product is right for you.

Similarities:

• The same durable, scratch resistant textile is used for both products.
• The height of the mesh is the same at 34 inches alpine.
• The mounting brackets used to install both products are the same.
• Both products come in the same color, White and Café (there is too a Blackness color option for Retract-A-Gate)
• Both products retract, automatically in the same fashion, into a 4-inch diameter curl.

Differences:

• The Bow Wow Barrier is for pet use only whereas the Retract-A-Gate is certified for utilize with dogs, pets, and children.
• The Bow Wow Bulwark is only used when opening your door, so your dog is unable to run exterior. Retract-A-Gate is used to block off an area in or out of the house for longer periods of time.
• Considering the Bow Wow Barrier is simply used when the door is opened, it does not need a lock; the Retract-A-Gate is equipped with a childproof lock to secure the gate in place.
• The Bow Wow Barrier opens and closes automatically when your door is opened or airtight. Retract-A-Gate can do this too, but information technology has other features which aren't needed for an intermittent door-opening type pet barrier.
• Retract-A-Gate is either 52 or 72 inches wide depending on the model; the Bow Wow Bulwark is only for exterior door use and will open to a maximum of 28 inches broad.
• The screws used to install the Bow Wow Barrier to the door are 1-inch long; all Retract-A-Gate screws are two-inches long so it tin be installed anywhere in and out of the abode.

lowetholuthe.blogspot.com

Source: https://retract-a-gate.com/retractable-pet-dog-gate-faq/

Share this post